Search results:

Foster 10-42

Foster 10-42

Foster 10-42 Pumpable Cold Sealer is a non-skinning, high solids, non-setting, seam and joint sealant for metal air ducts. It remains soft and flexible, preventing damage to the seal due to thermal cycling through a wide range of temperatures.

Foster Pumpable Cold Sealer has excellent adhesion to a wide variety of non-porous surfaces. It provides an air tight, long lasting seal for metal-to-metal joints and seams. Mechanical fasteners of the type and number normally used for duct assemblies are required to provide rigidity to the duct system.

Operating temperature: -46°C to 93°C.

Foster 30-16 WB

Foster 30-16 WB

Foster Fire Resistive Anti-Abrasion Coating is an off-white, high solid, water based fire resistive bore coating for the inner surfaces of cellular glass, rigid polyurethane, ureaformaldehyde, or polyisocyanurate foam insulation to reduce abrasion from vibration piping or vessels.

Its strong adhesive qualities through a wide temperature range permit its use on extremely low temperature and dual temperature equipment.

Operating temperature: -196 to 130°C. Intermittent to 392°F (to 200°C)

Foster 30-36 HF

Foster 30-36 HF

Foster Sealfas Coating is a white, tough, washable, abrasion-resistant indoor coating for thermal insulation. Sealfas Coating is also used as a lagging and lap adhesive for canvas and glass lagging cloth.

Foster 30-36 has excellent brushing characteristics which will result in better coverage and more uniformly coated surfaces.

Operating temperature: -18 to 82°C.

Foster 30-45

Foster 30-45

Foster Foamseal Sealant is a grey vapour barrier sealant designed for use with rigid thermal insulation including polystyrene foam. It remains flexible and tough in joints and will not shrink or crack during repeated cycles of high and low temperatures.

Foamseal Sealant seals the joints of cellular glass and other insulations against the entrance of moisture.

Operating temperature: -73 to 149°C.

Foster 30-60

Foster 30-60

Foster Thermfas® Heat Transfer Cement 30-60 is a black, water-base inorganic cement designed to improve the efficiency of conventional steam traced or electrical resistance heating systems.

The high thermal conductivity properties of 30-60 compare favourably with the full jacketed systems and enable a cost saving of 75 to 80%. Foster 30-60 works equally well in heating or cooling installations.

Foster 30-80

Foster 30-80

Foster Vapor-Safe Coating 30-80 is a white, water-base, fire-resistive, flexible, high solids vapour barrier finish for most types of thermal insulation, including polystyrene foam. It may be used over dry concrete, finishing cement, and most metals.

Vapor-Safe Coating has the water resistance and low water vapour permeance normally found in only solvent based products. It can be used in high humidity environments, and greatly retards water vapour permeation.

Operating temperature: -29 to 82°C

Foster 30-90

Foster 30-90

Foster Vapor-Safe Mastic 30-90 is a white, high solids water base, fire resistive, flexible vapour barrier finish for most types of thermal insulation, including polystyrene foam. It may be used over dry concrete, finishing cement, and most metals.

Vapor-Safe Mastic has the water resistance and low water vapour permeance normally found only in solvent based products. It can be used in high humidity environments, and greatly retards water vapour permeation.

Operating temperature: -29 to 82°C.

Foster 30-91

Foster 30-91

Foster Vapor-Safe Mastic 30-91 is a grey, high solids water base, fire resistive, flexible vapour barrier finish for most types of thermal insulation, including polystyrene foam. It may be used over dry concrete, finishing cement, and most metals.

Vapor-Safe Mastic has the water resistance and low water vapour permeance normally found only in solvent based products. It can be used in high humidity environments, and greatly retards water vapour permeation.

Operating temperature: -29 to 82°C.

Foster 31-31

Foster 31-31

Foster Insulfas® Coating 31-31 is a light-coloured, tough, washable, abrasion-resistant coating for thermal insulation. It is also used for cementing laps of canvas or lagging cloth.

It is compatible with expanded polystyrene, polyurethane foam, and other plastic foam insulations and can be used as a sealer coat to protect them from attack by solvents in chemical resistant finishes.

Operating temperature: -18 to 82°C.

Foster 32-17

Foster 32-17

Foster Safetee Duct Sealant is a light-grey, fire resistive, fibrated, water based, indoor/ outdoor vapour barrier sealant for low, medium and high velocity heating and air conditioning ducts.

It performs as a tough and flexible adhesive and sealant, forming a durable seal against air leakage when used with or without reinforcing tape or membrane.

Operating temperature: -7 to 93°C.

Foster 32-20

Foster 32-20

Good penetration/impregnation & good binding of fibres -yellow colour, premier penetrating type encapsulant, penetrates deeply and upon cure, forms a firm light-weight, damage-resistant surface.

Foster 32-21

Foster 32-21

Good penetration/impregnation & good binding of fibres -blue colour, premier penetrating type encapsulant, penetrates deeply and upon cure, forms a firm light-weight, damage-resistant surface.

Foster 32-22

Foster 32-22

Good penetration/impregnation & good binding of fibres -transparent colour, premier penetrating type encapsulant, penetrates deeply and upon cure, forms a firm light-weight, damage-resistant surface.

Foster 32-60

Foster 32-60

Very good penetration & slight bonding of fibres / Fibrelock on temporary surfaces & plastic enclosures - blue colour, specifically designed to facilitate removal of asbestos containing materials from various substrates.

Foster 32-61

Foster 32-61

Very good penetration & slight bonding of fibres / Fibrelock on temporary surfaces & plastic enclosures - transparent colour, specifically designed to facilitate removal of asbestos containing materials from various substrates.

Foster 32-80

Foster 32-80

Bridging encapsulant / Fibrelock on substrates from which asbestos is removed - mastic consistency material designed to abate the release of asbestos fibres from both conventional and spray applied ACM.

Foster 32-90

Foster 32-90

Excellent penetration & no fibre bonding -ready to use or dilutable- specially designed to thoroughly and effectively wet out asbestos, drastically reducing fibre fly associated.

Foster 36-10

Foster 36-10

Foster Weatherite Mastic is a white, water-based weather barrier mastic used for a wide variety of applications over most thermal insulations including polystyrene, poly-urethane, PIR, mineral fibre and closed-cell elastomeres.

Operating temperature: -29°C to 82°C.

Foster 36-25

Foster 36-25

Foster Weatherite Mastic is a grey, water-based weather barrier mastic used for a wide variety of applications over most thermal insulations including polystyrene, poly-urethane, PIR, mineral fibre and closed-cell elastomeres.

Operating temperature: -29°C to 82°C.

Foster 40-97 First Defense

Foster 40-97 First Defense

Foster® First Defense 40-97 is a proven hospital-grade disinfectant with a wide range of application areas. Use Foster 40-97 to safely disinfect schools, hospitals, hotels, office buildings, nursing homes, day care centers, transportation terminals, and other public and institutional facilities. 

Foster® First Defense 40-97 Disinfectant is intended for use on washable hard, nonporous surfaces of tables, countertops, cabinets, chairs, floors, walls, desks, doorknobs, showers, sinks, and other non-porous surfaces such as metal and finished woodwork, as well as coils and drain pans of air conditioning and refrigeration equipment and heat pumps.

It has demonstrated effectiveness against a broad spectrum of bacteria and viruses, such as norovirus and viruses similar to coronavirus disease 2019, COVID-19 (SARS-CoV-2) on hard, non-porous surfaces.

Determine the quantity of disinfectant you require with our easy to use Foster® 40-97 Consumption Calculator.

Foster 46-10

Foster 46-10

Foster Weatherite Mastic is a white, water-based weather barrier mastic used for a wide variety of applications over most thermal insulations including polystyrene, poly-urethane, PIR, mineral fibre and closed-cell elastomeres.

Operating temperature: -29°C to 82°C.

Foster 46-25

Foster 46-25

Foster Weatherite Mastic is a grey, water-based weather barrier mastic used for a wide variety of applications over most thermal insulations including polystyrene, poly-urethane, PIR, mineral fibre and closed-cell elastomeres.

Operating temperature: -29°C to 82°C.

Foster 57-73

Foster 57-73

Foster Heat Resistant Coating 57-73 is designed for use on stainless steel piping and equipment to protect from stress corrosion cracking due to the pressure of soluble chlorides in thermal insulations and surrounding atmospheres.

Foster 60-25

Foster 60-25

Foster C.I. Mastic is a black, tough, durable and high solids vapour barrier asphalt cutback mastic. Due to its low vapour permeance, it is an ideal surface coating for low temp insulation on outdoor applications.

C.I. Mastic may be used on heated lines, vessels and equipment in intermittent or dual temperature service to prevent the off periods or on cold cycles.

Operating temperature: -40°C to 82°C.

Foster 60-38

Foster 60-38

Foster Monolar II Mastic is a white, tough, flexible, fire-resistive elastomeric finish for protection of thermal insulation. It is also used as a vapour barrier finish for fittings. It is excellent for outdoor use where good colour retention, chemical resistance and durability are required.

Monolar II Mastic provides outstanding weather barrier and vapour barrier protection for most board stock thermal insulations except polystyrene.

Operating temperature: -40 to 121°C.

Foster 60-39

Foster 60-39

Foster Monolar II Mastic is a grey, tough, flexible, fire-resistive elastomeric finish for protection of thermal insulation. It is also used as a vapour barrier finish for fittings. It is excellent for outdoor use where good colour retention, chemical resistance and durability are required.

Monolar II Mastic provides outstanding weather barrier and vapour barrier protection for most board stock thermal insulations except polystyrene.

Operating temperature: -40 to 121°C.

Foster 60-44

Foster 60-44

Foster Stackfas Mastic is a black, high solids, non-asphaltic coatings with outstanding heat resisting properties. For use in boiler stacks and chimneys, both steel and concrete, to prevent corrosion from acid exhaust gases.

Operating temperature: -23 to 177°C.

Foster 60-75

Foster 60-75

Foster Fire Resistive Aluminium Mastic 60-75 is a weather- proof water vapour barrier designed to protect insulation systems applied to equipment operating below ambient temperatures located in most industrial environments.

Fire Resistive Aluminium Mastic 60-75 can be applied by glove, trowel or airless spray.

Operating temperature: -40 to 80°C.

Foster 60-90

Foster 60-90

Foster Monolar Mastic is a white, tough, flexible, and fire-resistive elastomeric finish for protection of outdoor thermal insulation. It's an excellent vapour barrier for low temperature insulation on tanks, pipework, vessels and fittings.

Monolar Mastic provides outstanding weather barrier protection, showing good colour retention, excellent chemical resistance, and durability.

Operating temperature: -46 to 104°C.

Foster 60-91

Foster 60-91

Foster Monolar Mastic is a grey, tough, flexible, and fire-resistive elastomeric finish for protection of outdoor thermal insulation. It's an excellent vapour barrier for low temperature insulation on tanks, pipework, vessels and fittings.

Monolar Mastic provides outstanding weather barrier protection, showing good colour retention, excellent chemical resistance, and durability.

Operating temperature: -46 to 104°C.

Foster 60-95

Foster 60-95

Foster Monolar Mastic is a white, tough, flexible, and fire-resistive elastomeric finish for protection of outdoor thermal insulation. It's an excellent vapour barrier for low temperature insulation on tanks, pipework, vessels and fittings.

Monolar Mastic provides outstanding weather barrier protection, showing good colour retention, excellent chemical resistance, and durability.

Operating temperature: -46 to 104°C.

Foster 60-96

Foster 60-96

Foster Monolar Mastic 60-96 is a grey, tough, flexible, and fire-resistive elastomeric finish for protection of outdoor thermal insulation. It's an excellent vapour barrier for low temperature insulation on tanks, pipework, vessels and fittings.

Monolar Mastic provides outstanding weather barrier protection, showing good colour retention, excellent chemical resistance, and durability.

Operating temperature: -46 to 104°C.

Foster 65-05

Foster 65-05

Foster Fire Resistive C.I. Mastic is a black, tough, durable, high solids vapour barrier and weather-coating for the protection of thermal insulation in outdoor service. Its excellent weather and fire resistance makes it suitable for use in place of conventional asphalt cutback mastic.

It is an ideal surface coating for low temperature insulating applications where the insulation used is not affected by mild solvents.

Operating temperature: -40 to 93°C.

Foster 65-05 WB

Foster 65-05 WB

Foster Mastic 65-05 WB is a black, tough, durable, high solids vapour barrier for the protection of indoor thermal insulation for in protected outdoor service.

Foster Mastic 65-05 WB is an asphalt cutback/ water-based mastic and can be used on all insulation materials including Polystyrene foam.

Operating temperature: -30 to 90°C.

Foster 65-06

Foster 65-06

Foster Fire Resistive C.I. Mastic is a black, tough, durable, high solids vapour barrier and weather-coating for the protection of thermal insulation in outdoor service. Its excellent weather and fire resistance makes it suitable for use in place of conventional asphalt cutback mastic.

It is an ideal surface coating for low temperature insulating applications where the insulation used is not affected by mild solvents.

Operating temperature: -40 to 93°C.

Foster 81-33

Foster 81-33

Foster Fire Resistive Adhesive is an off-white superior adhesive for cementing thermal insulation to all structural surfaces. It is quick-setting, with good specific adhesion to iron, steel, aluminium, and most thermal insulations.

It can be used without mechanical fastening for marine hull insulation. Fire Resistive Adhesive is the preferred adhesive for use with rigid polyurethane insulations. Operating temperature: -59 to 149°C.

Foster 81-82

Foster 81-82

Foster Adhesive 81-82 is a beige, solvent-free, flexible two parts adhesive, vapour barrier. It is suitable for a wide range of temperatures and can be used with all types of thermal insulation.

Foster Adhesive 81-82 provides high adhesion and is suitable for fixing all types of insulation materials to themselves or on numerous supports (rust-free metal, cement, plaster, wood, etc).

Operating temperature: -70 to 150°C.

Foster 81-84

Foster 81-84

Foster Adhesive Sealant is a two-component, high strength thermosetting urethane adhesive containing no flammable solvents. It is designed to bond various types of low- temperature insulation to themselves and to metal and masonry substrates.

After curing, it forms a strong, yet flexible bond capable of withstanding thermal shock and mechanical impact.

Operating temperature, on urethane foam -157°C to 93°C, on cellular glass -73°C to 93°C.

Foster 82-08

Foster 82-08

Foster Kold-Fas Adhesive is a black, low cost, high solids, quick setting, water base adhesive designed to adhere thermal insulation board and blanket (polystyrene foam, expanded polystyrene bead board, polyurethane foam, low density fibrous glass and cork) to metal, masonry, wood and to itself.

It is also used to adhere all types of vapour barrier facings, papers and polyethylene film to insulation and building surfaces.

Operating temperature: -46 to 77°C.

Foster 82-77

Foster 82-77

Foster Cryogenic Adhesive is a black, chemically-curing composition which develops high tensile strength and adhesion, at room temperature, to a variety of surfaces including metal, wood, masonry and polyester plastics.

It is supplied at virtually 100% solids enabling immediate bonding between non-porous surfaces without solvent entrapment problems. Cryogenic Adhesive also can be used as a joint sealer/ adhesive.

Operating temperature: -196 to 121°C.

Foster 82-88

Foster 82-88

Foster Slabtack 82-88 is a pale-straw coloured, solvent based rubber solution designed for bonding a variety of insulation materials to each other or to building surfaces, pipes, trunking, etcetera.

Operating temperature: -20 to 65°C.

Foster 84-20

Foster 84-20

Silica-based sprayable/brushable sealer to lock-down residual fibres on hot surfaces (up to 1200 degrees Celsius) from which asbestos has been removed, e.g. turbines, boilers, etc.

Foster 85-18

Foster 85-18

Foster 85-18 is the advised alternative to Foster 85-60 for use in Europe.

Foster 85-18 Adhesive is a cream coloured, high tack, fast-setting, water-base adhesive. It is designed for bonding low density duct liner, duct wrap, and fibrous glass insulations to painted or unpainted steel, galvanized or aluminium surfaces.

Foster 85-18 Adhesive is solvent free, non-flammable when wet and fire-resistive when dry.

Operating temperature: -29 to 98°C.

Foster 85-60

Foster 85-60

Please note: Due to REACH legislation Foster 85-60 is only available for delivery and use outside Europe. For use in Europe please consider Foster 85-18 as its alternative.

Foster 85-60 Adhesive is a cream coloured, high tack, fast-setting, water-base adhesive. It is designed for bonding low density duct liner, duct wrap, and fibrous glass insulations to painted or unpainted steel, galvanized or aluminium surfaces.

Foster 85-60 Adhesive is solvent free, non-flammable when wet and fire-resistive when dry.

Operating temperature: -29 to 98°C.

Foster 85-75

Foster 85-75

Foster Drion Contact Cement is an off-white, fast-setting, water-resistant adhesive for sealing the laps of vapour barrier jackets. Also used for bonding materials to a variety of surfaces in applications where immediate adhesion and high initial adhesive strength are required.

Especially suited for bonding two impermeable surfaces.

Operating temperature: -29 to 93°C.

Foster 90-10

Foster 90-10

Foster H.I. Mastic is a black, durable protective weather coat for use over thermal insulation where an economical breathing mastic is required. H.I. Mastic is an asphalt emulsion. It will not shrink or crack during curing.

It has good weathering stability and develops with its final resistance to acids, alkalies, abrasion and other abuses typical of outdoor industrial conditions.

Operating temperature: -18 to 93°C.

Foster 90-66

Foster 90-66

Foster Cryogenic Adhesive is a black, two-component, elastomeric adhesive/coating designed for use in cryogenic and specific chemical resistance applications. It is suitable for application to polyurethane foam, cellular glass and fibrous glass insulations in conjunction with aluminium, steel, wood and masonry construction materials.

Operating temperature: -196 to 121°C.

Foster 95-44

Foster 95-44

Foster Elastolar Sealant is an aluminium coloured, fire resistive, flexible butyl base elastomer based vapour barrier sealant. It is designed for sealing joints in insulation, metal and masonry wherever maintenance of a water-tight and air-tight seal is required.

Operating temperature: on urethane foam -101 to 93°C, on cellular glass -73 to 121°C, on flashing compound -40 to 121°C.

Foster 95-50

Foster 95-50

Foster Flextra Sealant is an off-white, one component, elastomer based product used as a vapour barrier sealant in the joints of cellular glass and urethane foam board stock insulations.

It remains soft and flexible, preventing damage to the insulation due to thermal cycling through a wide range of temperatures.

Operating temperature: on urethane foam -163 to 93°C, on cellular glass -100 to 93°C.

Foster 95-55

Foster 95-55

Foster F.R. Aluminium Metal Sealant is a metallic and mineral pigment filled co-polymer resin solution. It is easy to use and dries to a bright, reflective, durable finish with excellent weathering properties.

Foster F.R. Aluminium Metal Sealant is a weatherproof, durable material for use as a lap joint sealer for metal cladding. The metallic pigment of this flexible sealant enables it to blend with all bare metal finishes.

Operating temperature: -30 to 80°C.

Total items found: 50
insulated pipes